|Article From Houselogic.com
By: Oliver Marks
Published: December 04, 2009
If you're deciding whether to repair or replace central air conditioning equipment, assess the quality of your house's ductwork and
So much has changed in the world of air conditioning in recent years that if your system has almost any significant breakdown-or if it's
just not keeping you as cool as it used to-it may be worth replacing it instead of repairing it. As of 2010, for example, manufacturers must
use a new kind of refrigerant that's not an ozone-depleting chlorofluorocarbon. And a new system can use less than half the electricity of
your old one while doing a far better job of keeping you cool and comfortable.
If your air conditioner is more than eight years old, repair is probably not worth the expense, unless it's a simple problem like debris
clogging the condenser unit or a worn fan belt. Still, to best weigh your repair-or-replace decision, ask your contractor to assess not just
the condition of your existing equipment, but also the ducts that deliver the cool air and the overall quality of the insulation in your house.
Improving those elements might increase the effectiveness of the system as much or more than installing new machinery.
ASSESS THE EFFICIENCY OF YOUR CURRENT SYSTEM
Even if your central air conditioner is just eight to 10 years old, it could suck up to twice the electricity that even a low-end new one would
use. That's because it operates at or below 10 SEER, or Seasonal Energy Efficiency Ratio, which is the amount of energy needed to
provide a specific cooling output. Until 2006, 10 SEER was standard, but these days, the minimum allowed by federal law is 13 SEER.
That translates to 30% less electrical consumption and 30% lower cooling bills than equipment installed just a few years ago.
For an 1,800 square foot house, a new 13 SEER unit will cost $3,000 to $4,000. You can double your energy savings by jumping up to 16
SEER, which will reduce cooling expenses by 60% over a 10 SEER unit. At $5,000 to $6,000, these super-efficient units are more
expensive, but they qualify for a 30% federal tax
credit(http://www.houselogic.com/articles/tax-credits-replacing-heating-and-cooling-systems/) of up to $1,500 and possibly local
incentives, too. So the added cost might be negligible.
"Your installer can run the numbers for you to see whether it's worth the additional cost," says Ellis Guiles of TAG Mechanical in Syracuse,
New York. "If you're south of the Mason Dixon line, certainly, you can make up those dollars pretty quickly."
INSPECT THE CONDITION OF THE DUCTWORK
You could upgrade to the highest efficiency gear available and still not feel comfortably cool on hot days. That's because the mechanicals
are only part of the central air system. The average house's ductwork leaks 10% to 30% of its air before it can reach your living space,
according to Pacific Gas & Electric. Before deciding whether to repair or replace your condenser and blower units, your technician should
run a duct-leakage test, by sealing the vents and measuring how much air escapes the system.
If the ducts are inefficient, he can locate and seal the gaps, typically for $25 to $35 per vent (per "run" in industry jargon), or replace the
ductwork entirely with new, insulated pipe for around $100 per run, according to Guiles. Your technician may recommend doing the duct
improvements in conjunction with replacement of the mechanicals or may recommend only one or the other job.
CONSIDER THE BUILDING ENVELOPE ITSELF
If your house is poorly insulated, it's putting a strain on your aging air conditioner. Resolving the house's flaws may mean that your old
system will have enough cooling power to continue to do the job for a few more years. Or it may enable you to buy a smaller replacement
system, lowering your upfront and ongoing energy costs significantly.
Your heating and cooling contractor should assess and, if necessary, upgrade the building envelope. For example, he might seal gaps and
cracks(http://www.houselogic.com/articles/8-easy-ways-seal-air-leaks-around-house/) in the outer walls and attic floor, or he might blow
insulation(http://www.houselogic.com/articles/save-money-with-insulation-upgrade/) into the walls, either of which could knock as much as 30% off your heating and
cooling costs. This work too may be eligible for federal and local tax credits-and in some cases, it may be a more effective solution to your cooling problems than replacing
MAKE SURE A NEW SYSTEM IS SIZED RIGHT
If you decide to replace, make sure the contractor's bid includes a load calculation, which is a computer printout showing how big a
system you need and why.
Air conditioning is measured by the ton, which is the cooling power of a one-ton block of ice melting in 24 hours. Some old-school
installers use a ballpark estimate for sizing equipment-say, one ton for every 400 or 600 square feet of living space. But that typically
leads to systems that are too big, according to Greg Gill of Action Air Conditioning and Heating in San Marcos, Calif. Not only do oversized
systems cost more, but they also do their cooling work too quickly, which means more frequent on/off cycles, wearing out components
and gobbling electricity. Plus, they don't have a chance to effectively dehumidify the air.
Good contractors use load-calculating software that factors in such data as the number of windows in your house, the thickness of
insulation, the configuration of the attic, and the building's orientation to the sun. It produces not only an exact tonnage requirement, but
determines how much cool air each room needs. All bids (get at least three, from licensed, well-regarded companies) should include
this one-page printout.
A former carpenter and newspaper reporter, Oliver Marks has been writing about home improvements for 16 years. He's currently
restoring his second fixer-upper with a mix of big hired projects and small do-it-himself jobs.
Reprinted from HouseLogic (houselogic.com) with permission of the NATIONAL ASSOCIATION OF REALTORS (R).
Copyright 2010. All rights reserved.
JK Realty 1760 E Pecos Rd Ste 338 Gilbert AZ 85295
Cell: 602.909.4906 E-mail: firstname.lastname@example.org